New: Drop-in replacement for Change Healthcare APIs

EDI 848 Material Safety Data Sheet

Functional Group MS

X12M Supply Chain Subcommittee

This X12 Transaction Set contains the format and establishes the data contents of the Material Safety Data Sheet Transaction Set (848) for use within the context of an Electronic Data Interchange (EDI) environment. The transaction set can be used to communicate chemical characteristics, hazards, and precautions for the safe handling and use of a material. The transaction set is intended to convey the information required for a Material Safety Data Sheet (MSDS) as defined by the Occupational Safety and Health Administration (OSHA) Hazard Communication Standard, 29 CFR 1910.1200 in the United States, and Workplace Hazardous Materials Information System (WHIMS) in Canada, and various state, province, and local requirements under right-to-know legislation. The MSDS provides the receiver with detailed information concerning material identity, emergency response, chemical and physical characteristics, toxicology, and industrial hygiene procedures. State and federal law dictate who is obligated to provide the MSDS and to whom it should be issued. In addition, third-party providers or others with no statutory obligation may voluntarily provide an MSDS to anyone. This transaction set allows for transmission of MSDS data in a structured, unstructured, or semi-structured form. CAUTION: With this transaction set, text format is critical due to the MSDS's primary role as a vehicle for hazards communication. The risk if this information is not transmitted clearly and accurately could be harmful to human life, harmful to the environment, could cause mishandling of product, could result in regulatory non-compliance, and could result in liability. Trading partners need to agree on how to interpret, store, and display/print MSDS text, especially text contained in the MSG and SD1 segments. For example, a sender may wish to format text so that one print line is mapped to one MSG segment. Segment terminator and data element delimiter characters shall not appear in any MSDS data. WARNING: Alteration of the original document will occur if the EDI translator or application software converts characters to uppercase. This may adversely affect the appearance, effectiveness, clarity, readability, and communicability of the printed MSDS document.

Heading

Position
Segment
Name
Max use
  1. To indicate the start of a transaction set and to assign a control number

  2. To indicate the beginning of the Material Safety Data Sheet Transaction Set, identify the distinct type of report, and transmit key identifying numbers and dates relating to that report

  3. To transmit information in a free-form format, if necessary, for comment or special instruction

  4. To specify identifying information

  5. To specify pertinent dates and times

  6. N1 Loop Optional
    Repeat >1
    1. To identify a party by type of organization, name, and code

    2. To specify additional names

    3. To specify the location of the named party

    4. To specify the geographic place of the named party

    5. To specify identifying information

    6. To identify a person or office to whom administrative communications should be directed

Detail

Position
Segment
Name
Max use
  1. LIN Loop Optional
    Repeat >1
    1. To specify basic item identification data

      LIN loop is product level. MSS is section level. The first SD1 loop is safety data relating to the section only. The first CID loop is for complex measurements on safety data. LX loop is used to specify product characteristics, components, or complex measurements (i.e., those with environmental parameters). The second SD1 loop is safety data relating to a particular product characteristic or component. The second CID loop is for complex measurements on safety data, which related to a particular product characteristic or component.
    2. To describe a product or process in coded or free-form format

    3. MSS Loop Optional
      Repeat >1
      1. To identify the report section

        Regulation notifications can be contained in MSS or SD1 or both.
      2. To specify physical measurements or counts, including dimensions, tolerances, variances, and weights (See Figures Appendix for example of use of C001)

      3. To provide a free-form format that allows the transmission of text information

        Trading partners must agree on a convention for text processing that will not split words, and which can convey correct meaning, in successive SD1 or MSG segments.
      4. SD1 Loop Optional
        Repeat >1
        1. To provide safety data information to recipients of the transaction, including identification of the hazard that the material being described represents, and the organization or party which declared this material to be a hazard or established exposure limits or other guidelines for that material

          Regulation notifications can be contained in MSS or SD1 or both.
        2. To specify physical measurements or counts, including dimensions, tolerances, variances, and weights (See Figures Appendix for example of use of C001)

        3. To describe marking, packaging, loading, and unloading requirements

        4. To specify transportation special handling requirements, or hazardous materials information, or both

        5. To provide a free-form format that allows the transmission of text information

          Trading partners must agree on a convention for text processing that will not split words, and which can convey correct meaning, in successive SD1 or MSG segments.
        6. CID Loop Optional
          Repeat >1
          1. To specify the general class or specific characteristic upon which test results are being reported or are to be taken

          2. To specify physical measurements or counts, including dimensions, tolerances, variances, and weights (See Figures Appendix for example of use of C001)

      5. LX Loop Optional
        Repeat >1
        1. To reference a line number in a transaction set

        2. To specify the general class or specific characteristic upon which test results are being reported or are to be taken

        3. To specify physical measurements or counts, including dimensions, tolerances, variances, and weights (See Figures Appendix for example of use of C001)

        4. To provide summary statistics related to a specific collection of test result values

        5. To describe the nature of the test performed

        6. To provide a free-form format that allows the transmission of text information

        7. SD1 Loop Optional
          Repeat >1
          1. To provide safety data information to recipients of the transaction, including identification of the hazard that the material being described represents, and the organization or party which declared this material to be a hazard or established exposure limits or other guidelines for that material

          2. To specify physical measurements or counts, including dimensions, tolerances, variances, and weights (See Figures Appendix for example of use of C001)

          3. To describe marking, packaging, loading, and unloading requirements

          4. To specify transportation special handling requirements, or hazardous materials information, or both

          5. To provide a free-form format that allows the transmission of text information

          6. CID Loop Optional
            Repeat >1
            1. To specify the general class or specific characteristic upon which test results are being reported or are to be taken

            2. To specify physical measurements or counts, including dimensions, tolerances, variances, and weights (See Figures Appendix for example of use of C001)

Summary

Position
Segment
Name
Max use
  1. To indicate the end of the transaction set and provide the count of the transmitted segments (including the beginning (ST) and ending (SE) segments)

Stedi is a registered trademark of Stedi, Inc. Stedi's EDI Reference is provided for marketing purposes and is free of charge. All names, logos, and brands of third parties listed on our site are trademarks of their respective owners (including “X12”, which is a trademark of X12 Incorporated). Stedi, Inc. and its products and services are not endorsed by, sponsored by, or affiliated with these third parties. Our use of these names, logos, and brands is for identification purposes only, and does not imply any such endorsement, sponsorship, or affiliation.